If you find there is any copyright abuse, contact us as soon as possible, thanks.
A Good Cause
03/24/2008, 02:29 | Musings From My Shop
It?s no secret that I?m a fan of the work of Greene & Greene. A big fan. Anyone with cursory knowledge of the brothers has heard of the Ultimate Bungalows. These homes, designed by Charles and Henry at the height of their popularity and creative energy, are grand residences built with uncompromising attention to detail. Everyone agrees the the Gamble, Blacker, Pratt and Thorsen houses are in this category. Many include the Freeman Ford house as well. Were I the ultimate authority, the Robinson house would also join the list.
While the Gamble house remained in the Gamble family until it was donated to USC and the city of Pasadena, the other Ultimates have more colorful histories. Most endured some period of neglect or abuse. The rape of the Blacker house resulted in ordinances that protect historic homes in Pasadena. I think the Thorsen house trumps them all, however. Since 1942 the Thorsen house has been home to a fraternity.
I suspect that many of you have seen the movie ?Animal House.? It?s hilarious. It?s a classic. It?s completely unlike the California (Berkeley) chapter of Sigma Phi. The brothers of Sigma Phi take their stewardship of the Thorsen house, which the fraternity purchased from the Thorsen estate, very seriously. Every Saturday morning they work as a group on maintaining the house. They learn its history. They take pride in it.
But keeping up with the demands of a 100 year old mansion (and a work of art at that) is difficult. And expensive. About 9 million dollars. If you find yourself in Berkeley, stop by the house. The brothers will happily give you a tour and accept a donation to the fund. But don?t let an inability to visit stop you from contributing. Send a few dollars and help save an historic landmark, one of the Ultimates. It?s a lot easier to keep such houses around than to wait for another genius to come along and design more.
The Thorsen House Restoration Campaign
c/o Mr. Dan McNear
Route 1
Box 264-E
San Rafael, CA 94901
History Of Traditional Kudus House
06/26/2007, 11:15 | Antique Knockdown Carved Wood House Kudus is a city in the Central Java, Indonesia, located among Jepara, Demak, Pati, and Purwodadi districts and in the route of Semarang the capital city of Central Java to Surabaya (please see location map). Based on story, Kudus name was from Al-Quds, which mean holy.
Traditional house of Kudus if notice deeply is more and more fabulous since its uniqueness and attractiveness in exterior and interior which full with ornamen that made by highest skill woodcarving artist. Foundation of the existancy of the traditional house of Kudus was full with taste and creation that fashioned in the beautiful forms without broken any religion values. Through the activity of art, there is possibility of adding the atmosphere of the deepest metaphysic reality.
Ancient Kauri Wood Ring Wedding - Promise Set
00/00/0000, 00:00 | Wood Rings by Simply Wood Rings
When I work with a wood that is this old it puts things into perspective in a very real way. I think of life without our minds trappings. Not empty but more full of what life really is.
Imagine for a moment what nature has done for us to have this natural miracle of our life from so long ago. This ring gives you a connection to an extraordinary time of pre-historic sunlight, rains and life from so long ago.
To see more visit my Shop at: http://www.simplywoodrings.com
00/00/0000, 00:00 | Wood Rings by Simply Wood Rings

This ring is made from Ancient Kauri wood and 99.9% pure fine silver.
Greene and Greene from a Woodworker's Perspective
00/00/0000, 00:00 | Popular Woodworking
The series of articles by David Mathias on Greene and Greene feature photos that are different than any that I have ever seen. The first article, the August 2008 issue of Popular Woodworking presented an overview of the style. The second article, in the October 2008 issue focuses on the furniture and joinery details. The October issue is due from the printer any time now, and will soon be on its way to subscribers. As was the case in August, we had more photos than we had room for in print, so we are putting the extras online in PDF format.
My favorite thing about these photos is the point of view and attention to detail that comes from having a fellow woodworker behind the camera. Several of the photos are of familiar pieces, but you will see construction details you haven't seen before. Many of the photos are of objects that are rarely if ever seen. This is a rare opportunity to get a closer look at an amazing body of work, through the eyes of someone who knows what you want to see.
Click the link below to download the PDF slide show of additional photos.
0810GnGSlides.pdf (1.45 MB)
The slide show from the August article is available by clicking here
--Bob Lang
Autumn 2008 Issue is Underway
00/00/0000, 00:00 | Woodworking blog Woodworking Magazine
Learning
to cut woodworking joints is one thing. Figuring out how to assemble all those joints
in a correct and efficient order for a project is another skill entirely.
In the upcoming Fall 2008 issue of Woodworking Magazine, we're delving deep
into the topic of cabinet construction. And the method we have developed during the
last decade is different than any other you have read, but it will do three things
for your woodworking:
1. You'll make fewer mistakes and waste less wood.
2. You'll have an easier time fitting your doors and drawers.
3. Your cabinets will go together faster with tighter joints.
If you'd like to learn about our new method, then I encourage you to subscribe to
the magazine by May 30 to guarantee you will receive a copy of the Fall 2008 issue.
In addition to our research into cabinet construction, you'll also find:
Fitting Doors & Drawers: We show you how to square up doors with a table
saw and fit it precisely with a hand plane. Plus, we explain how to size your drawers
so they'll fit properly with only minor adjustments with a plane.
Tool Review – Sliding Bevels: Why do so many of them slip and slide around
on you? We investigate the major brands available today and find the best ones.
Coloring Walnut: Walnut with a simple clear finish looks cold and lifeless.
We show you how to warm up this beautiful wood with a variety of approaches, including
shellac and stains.
So why should you subscribe to Woodworking Magazine? We think it's different
than every other magazine out there. It's written to help all woodworkers fill in
the inevitable gaps in our skills that result from teaching ourselves woodworking.
We show you the historical, time-tested and frequently forgotten methods to saw any
joint, drawboring, wedged through-tenons and splines. We review tools that other magazines
won't touch but are extremely important: like 6" rules, screws, combination squares
and moisture meters.
Plus, we offer projects you won't elsewhere. We build only time-tested forms in classic
styles, such as Arts & Crafts, Shaker and early American. More importantly, we
pick projects that can be built without an enormous outlay of time, wood or tools.
And that's not all that's different. Woodworking Magazine has no advertisements
and is printed in glorious sepia-toned black-and-white on its inside pages.
If you're ready to subscribe, we're ready to take your order. Click
here and we'll sign you up to receive the next issue.
— Christopher Schwarz
Nothing Magic About My Rag
00/00/0000, 00:00 | Woodworking blog Woodworking Magazine
Sometime back in 1996 I took a piece of cloth that was cast off from my wardrobe.
I cannot remember what the garment was. A sweatshirt perhaps? Long underwear? It’s
a bit stretchy. And I soaked the sucker in WD-40.
Since that day, I have soaked that rag with every kind of oily substance you can imagine.
Here’s the short lubricant list: Camellia,
3-in-1, Jojoba, mineral spirits,
thread-cutting oil, spray-on “dry” shop lubricant and oil from various recesses of
my personhood (yes, it’s true, and historically correct. Ask me over a beer sometime).
I use this rag to wipe down every tool after I use it. I lubricate my plane soles
with it while working. I use it to wipe off the sharpening slurry from my tools after
honing them.
And what I’m about to say will upset people who know anything about chemistry: I have
never suffered any ill effects from this nefarious mixture when finishing my projects
using any of the known finishing compounds: shellac, lacquer, oil, varnish, wax and
all of their wacky combinations. No fish-eye has ever appeared in my finish. No orange
peel. No silicone contamination.
So what gives? How have I cheated the finishing gods for 12 full years?
Probably because of the cutting action of all tools. When I wipe down a tool – a sawblade
or a handplane – I leave the thinnest coat possible behind. This thin film is all
I need to protect the tool from rusting. Then, when I apply the tool to the work,
there is little doubt that some of this lubricant winds up on my work.
This first cut removes the lubricant from the tool. Then my next pass with the tool
removes the wood that has the lubricant on it. Problem solved.
In addition to my magic rag (Lucy, my wife, calls it my “woobie”), I also am very
fond of the Sandflex blocks from Klingspor to
remove rare and errant spots of rust or staining that show up on my tools. These spongy
“rust erasers” are like rubber that has been impregnated by a mild abrasive. The blocks
will abrade your tools, but only slightly – in most cases less than steel wool. One
block (I like the “medium” and “fine”) will last for decades of normal use.
As a result, I have had few problems with rust on my tools, despite the fact that
I live outside a humid river city (Cincinnati) and my home shop is in a basement.
The bottom line is that diligence is far more important than the brand of lubricant.
— Christopher Schwarz
P.S. Below is my latest project with a shellac and lacquer finish with no finishing problems. Maybe next project....
My Town Tour - Brezno, Slovakia
00/00/0000, 00:00 | LumberJocks.com :: woodworking showcaseI’d like to invite you to a brief tour of Brezno – nice small town in the heart of Slovakia where I’m living now.

Let’s see what Wikipedia has to say about Brezno’s history:
“The place has been inhabited since prehistoric times, but the current town arose from an old Slovak settlement, next to which newly arrived German miners erected a typical square market in the early 13th century. The first written evidence of the town’s existence is dated 1265 when King Béla IV of Hungary issued a charter for the hunters from the area of Liptov allowing them to use woods around the settlement, known as Berezuno. The name is derived from the Slovak word “breza” for birch. In the nineteenth century Brezno was a typical almost purely Slovak town and was one of the centres of the Slovak national movement. Since Second World War it has developed into an industrial town.”
“According to the 2001 census, the town had 22,875 inhabitants.”
... and this is interesting info too: “Brezno is twinned with the French town of Meudon, Nový Bydžov in the Czech Republic and Ciechanów in Poland.”
Tour continues with some beautiful photos. Enjoy…
History

From the sky

Courthouse
Town square

Panorama

Storm
Gray Bear golf course near Brezno

Low Tatras in winter
Wikipedia's page about Brezno
Nice article at Spectacular Slovakia
Beautiful photos of the region at Hiking.sk
Map of the Upper Hron River Region
Thanks to jeanmarc for posting his region tour today. He inspired me ;)
Hope you enjoyed!
Episode 3 - Bombe Series - Tommy visits RISD Museum
00/00/0000, 00:00 | T Chisel - The Rough Cut Show!Figuring Out Finger Joints
00/00/0000, 00:00 | Woodworking blog Woodworking Magazine
For me, finger joints have always been the nerdy, square cousin to the dovetail.
Finger joints are immensely strong when glued properly. But they are usually used
by beginning woodworkers in places where a dovetail would be more appropriate, such
as on a piece of 18th-century casework.
Add to that the fact that finger joints are tricky or dangerous to make on wide boards
(without a commercial jig) plus the fact that gluing them with yellow glue is stressful,
and it's a wonder that anyone uses them at all.
And so we decided to tackle finger joints for the Summer 2008 issue of Woodworking
Magazine, which will be shipping to subscribers next month. It took us a few months
to really pin them down (pun intended), but I think we nailed it (and no, cut nails
are not involved).
Here's a small taste of some of the problems of the joint we solved after three months
of testing in our shop:
Appearance: Finger joints are a product of the machine age. Using them in styles
before circa 1900 is just wrong to the eye. So consider the joint for more contemporary
pieces only.
Cutting them Accurately: Right now there are basically two different ways to
cut the joint: A shop-made jig for the table saw for narrow boards, and using a router
jig that costs several hundred dollars for wide boards. We set out to develop a simple
and safe shop-made jig that could handle both wide and narrow boards. Senior Editor
Robert W. Lang had a stroke of genius on this and solved the problem forever (in my
opinion).
Gluing Them Easily: You can assemble small boxes with finger joints fairly
easily when using yellow glue. But at a certain point, you hit the wall because the
glue sets up before you can close all the joints. So the solution would seem to be
a slow-setting glue. Well, that's one way to go about it. But we found an easier and
faster way that is super-strong (see the photo of Managing Editor Megan Fitzpatrick's
boot on a sample joint). In the end, it took an anvil to bust up our sample joints.
Also in the Summer 2008 Issue
The finger joint is just one of the major themes running through the issue. Here are
some of the other stories you can look for in the coming issue:
Building a Better Chest: Most woodworkers build chests using the most convoluted
and fussy assembly imaginable. After reviewing hundreds of historical models, we settle
on a method for building a chest that looks more complex at first glance, but actually
saves an immense amount of shop time, requires less fussing around and allows more
design flexibility.
Crackle Finishing: Many woodworkers who try a crackle finish have inconsistent
results. Sometimes it works; sometimes it doesn't. And predicting how much it's going
to crackle is almost impossible. Senior Editor Glen D. Huey cracks the code of crackle
finish and finds out that the easiest and most predictable way to do it is also the
simplest.
Trimming End Grain: When you have to cut back some end grain so it's flush
with some face grain, it's always an opportunity to mess up the project. We show you
two (actually three) methods for doing it right every time with a block plane, sander
and pencil eraser.
And one more thing about the Summer 2008 issue: This issue is going to be mailed out
to subscribers in a protective plastic bag, which will reduce the chances that the
postal service will mangle it. If the plastic bag works for you, let us know so we
can encourage our manufacturing division to continue using it.
And if you're not a subscriber, you can easily remedy that here.
Eco-friendly Pre-historic Wooden Ring
00/00/0000, 00:00 | Wood Rings by Simply Wood Rings
This ring is made from Ancient Kauri which is the world's oldest wood at 50,000 years old.
When I work with a wood that is this old it puts things into perspective in a very real way. I think of life without our minds trappings. Not empty but more full of what life really is.
Imagine for a moment the what nature has done for us to have this natural miracle of our life from so long ago. This ring gives you a connection to an extraordinary time of pre-historic sunlight, rains and life from so long ago.
Click to see the ring Eco-friendly Pre-historic Wooden Ring
http://www.simplywoodrings.com

